Latest Cisco CCNP 642-902 ROUTE Real Exam Download 341-350

Ensurepass

QUESTION  341

Which three steps are most helpful in verifying proper route redistribution? (Choose three.)

 

A.       On the routers not performing the route redistribution, use the show ip route command to see if the redistributed routes show up.

B.       On the ASBR router performing the route redistribution, use the show ip protocol command to verify the redistribution configurations.

C.       On the ASBR router performing the route redistribution, use the show ip route command to verify that the proper routes from each routing protocol are there.

D.       On the routers not performing the route redistribution, use the show ip protocols command to verify the routing information sources.

E.        On the routers not performing the route redistribution, use the debug ip routing command to verify the routing updates from the ASBR.

 

Correct Answer: ABC

 

 

QUESTION  342

A router is configured for redistribution to advertise EIGRP routes into OSPF on a boundary router. Given the configuration:

clip_image001

What is the function of the 25 parameter in the redistribute command?

 

A.       It specifies the seed cost to be applied to the redistributed routes.

B.       It specifies the administrative distance on the redistributed routes.

C.       It specifies the metric limit of 25 subnets in each OSPF route advertisement.

D.      It specifies a new process-id to inject the EIGRP routes into OSPF.

 

Correct Answer: A

 

QUESTION  343

Refer to the exhibit. R1 and R2 belong to the RIP routing domain that includes the networks 10.20.0.0/16 and 10.21.0.0/16. R3 and R4 are performing two-way route redistribution between OSPF and RIP. A network administrator has discovered that R2 is receiving OSPF routes for the networks 10.20.0.0/16 and 10.21.0.0/16 and a routing loop has occurred. Which action will correct this problem?

 

clip_image002

 

A.       Apply an inbound ACL to the R2 serial interface.

B.       Change the RIP administrative distance on R3 to 110.

C.       Configure distribute-lists on R3 and R4.

D.      Set the OSPF default metric to 20.

E.       Change the OSPF administrative distance on R3 to 110.

 

Correct Answer: C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION  344

Observe the exhibit. If the command variance 3 were added to RTE, which path or paths would be chosen to route traffic to network X?

 

clip_image003

 

A.       E-B-A

B.       E-B-A and E-C-A

C.       E-C-A and E-D-A

D.      E-B-A, E-C-A and E-D-A

 

Correct Answer: B

 

 

QUESTION  345

Which three statements are true regarding EIGRP? (Choose three.)

 

A.       By default, EIGRP performs auto-summarization across classful network boundaries.

B.       EIGRP uses an area hierarchy to increase network scalability.

C.       To speed convergence, EIGRP attempts to maintain a successor and feasible successor path for each destination.

D.      EIGRP uses hellos to establish neighbor relationships.

E.       By default, EIGRP uses the Dijkstra algorithm to determine the best path to a destination network based on bandwidth and delay.

 

Correct Answer: ACD

 

QUESTION  346

Refer to the graphic. What optional EIGRP configurations will be required in order to achieve full connectivity within AS 100?

 

clip_image005

 

A.       Use the EIGRP no auto-summary command on R1 and R2.

B.       Use the EIGRP no auto-summary command on R3 and R4.

C.       Use the passive interface on the R1 and R2 interface that connects to the 10.1.1.0/24 and 10.1.2.0/24 subnet respectively.

D.      Use the passive interface command between the R3 and R1 connection and between the R3 and R2 connection.

E.       Use the variance command on R3.

 

Correct Answer: A

 

 

QUESTION  347

Based on the P1R3 show ip bgp output, which statement is true?

 

clip_image007

 

A.       The best path to reach the 192.168.11.0 prefix is via 10.200.200.11.

B.       The best path to reach the 192.168.11.0 prefix is via 10.200.200.12.

C.       The best path to reach the 192.168.11.0 prefix is via both 10.200.200.11 and 10.200.200.12; BGP will automatically load balance between the two.

D.      The 192.168.11.0 and 192.168.12.0 prefixes were learned via EBGP from the 10.200.200.11 and 10.200.200.12 EBGP neighbors.

 

Correct Answer: B

 

 

QUESTION  348

Which two statements are EIGRP characteristics? (Choose two.)

 

A.       Updates are sent as multicast.

B.       Updates are sent as broadcast.

C.       Metric values are represented in a 32-bit format for granularity.

D.      LSAs are sent to adjacent neighbors.

 

Correct Answer: AC

 

 

QUESTION  349

What is the purpose of the eigrp stub configuration command?

 

A.       to increase scalability by limiting the EIGRP query range

B.       to reduce the size of the routing table by blocking the D EX (External EIGRP) routes into the EIGRP stub router

C.       to reduce the convergence time by enabling the EIGRP stub router to propagate the EIGRP queries from the EIGRP hub router

D.      to reduce the convergence time by enabling the EIGRP stub router to also perform query requests to the EIGRP hub router

 

Correct Answer: A

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION  350

Which command should be added to RTB under router bgp 100 to allow only the external OSPF routes to be redistributed to RTC?

 

clip_image009

 

A.       redistribute ospf 1

B.       redistribute ospf 1 match external 1

C.       redistribute ospf 1 match external 2

D.      redistribute ospf 1 match external 1 external 2

 

Correct Answer: D

 

 

Download Latest Cisco 642-902 ROUTE Real Free Tests , help you to pass exam 100%.