[Free] Download New Latest (September 2016) Cisco 300-070 Actual Test 121-130

Ensurepass

QUESTION 121

Refer to the exhibit. When users call number 00044156789453, they have to wait for several seconds before the call is sent. Which action sends the call immediately?

 

clip_image002

 

A.

In the translation pattern, change the CSS.

B.

In the route pattern, check the Allow Device Override check box.

C.

In the route pattern, check the Urgent Priority check box.

D.

In the translation pattern, check the Route Next Hop By Calling Party Number check box.

 

Correct Answer: C

 

 

QUESTION 122

The Cisco IP Phone of your company operator is on extension 7000. However, users normally dial 0 to get the operator. Which action sends calls that were made to 0 to the operator?

 

A.

Create a route pattern of 0 and use a called party transform mask of 7XXX.

B.

Create a translation pattern for 7000 and a called party transform mask of 0.

C.

Create a translation pattern for 0 and a called party transform mask of 7000.

D.

Create the IP phone overlay feature so the operator’s line has 0 and 7000 assigned to it.

E.

Create a translation pattern for 0 and a calling party transform mask of 7000.

 

Correct Answer: C

 

 

QUESTION 123

Which statement about the DiffServ QoS deployment architecture is true?

 

A.

DiffServ does not differentiate traffic types and thus cannot provide service levels.

B.

DiffServ architecture differentiates and classifies various types of traffic and provides several levels of service based on that classification.

C.

Resource Reservation Protocol is an example of a DiffServ mechanism where each router on the path for packet transmission is informed of the upcoming packet stream.

D.

DiffServ architecture provides QoS by assuring treatment for a specific traffic flow.

 

Correct Answer: B

 

 

QUESTION 124

Which two codecs are required for Cisco WebEx Enabled TelePresence? (Choose two.)

 

A.

G.711 codec for audio

B.

H.264 codec for video

C.

G.729 codec for audio

D.

G.711 or G.729 codec for audio

E.

H.263 codec for video

F.

H.264 or H.263 codec for video

 

Correct Answer: AB

 

 

QUESTION 125

After you configure a dial plan to call a particular prefix in the PSTN, you notice that some outbound calls are taking longer than usual (15 seconds) before you hear a connecting tone. What is the likely cause of this issue?

 

A.

The outbound gateway must be configured with the new prefix.

B.

The endpoint is choosing the best codec to use.

C.

The new prefix is overlapping other route patterns.

D.

With some prefixes, this is normal behavior of the PSTN.

 

Correct Answer: C

 

 

 

QUESTION 126

Refer to the exhibit. When a user dials 919005551212, the call fails. Which change do you need to make for this call to be successful?

 

clip_image004

 

A.

Change the route partition.

B.

Change the gateway or route list.

C.

Change the
route pattern to the correct number of digits.

D.

Change the call classification to OnNet.

E.

Change the route option.

 

Correct Answer: E

 

 

QUESTION 127

A Cisco Unified Communications Manager group specifies a prioritized list of how many Cisco Unified Communications Managers?

 

A.

0

B.

1

C.

2

D.

3

E.

4

F.

5

G.

6

H.

7

 

Correct Answer: D

 

 

QUESTION 128

What is the recommended default value that is used between regions for video calls?

 

A.

384 Kbps.

B.

G.722.

C.

G.711.

D.

G.728.

 

Correct Answer: A

 

 

QUESTION 129

Which configuration output indicates a properly configured T1 digital voice interface?

 

A.

controller T1 0/0/0

framing esflinecode b8zs

pri-group timeslots 1-24

!

B.

isdn switch-type primary-ni

!

controller T1 0/0/0

framing esflinecode b8zs

!

C.

isdn switch-type primary-ni

!

controller T1 0/0/0

framing esflinecode b8zs

pri-group timeslots 1-24

isdn switch-type primary-ni

!

D.

isdn switch-type primary-ni

!

controller T1 0/0/0

framing esflinecode b8zs

!

dial-peer voice 1 potsdestination-pattern 54….direction-inward.dialport 0/0/0:23

 

Correct Answer: C

 

 

QUESTION 130

Which command is used to enter the DSP farm profile configuration mode?

 

A.

dspfarm-profile 100 transcode

B.

dspfarmprofile 100 transcode

C.

dspfarm profile 100 transcode

D.

dspfarm 100 profile transcode

 

Correct Answer: C

 

Free VCE & PDF File for Cisco 300-070 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …