Refer to the Exhibit.
Routers in the Diagram are configured with EIGRP. If RTB and RTC fail, which action will RTA take with respect to the HQ network?
A. RTA will automatically route packets via RTD to the HQ network.
B. RTA will place the route via RTD into the hold down state.
C. RTA will go into the active state for all routers.
D. RTA will go into the active state for the route to HQ network.
Correct Answer: D
Refer to the exhibit. Which interoperability technique implemented on the router would allow Host-1 to communicate with Host-2?
A. Dual Stack
C. 6to4 tunnel
D. GRE tunnel
E. ISATAP tunnel
Correct Answer: B
Refer to the exhibit. Which statement is true?
A. RTA will redistribute the RIP routers into the NSSA as type 7 LSAs. RTB will translate the type 7 LSAs into type LSAs and flood them throughout the OSPF backbone.
B. RTA will redistribute the RIP routers into the NSSA as type 7 LSAs. RTB will flood the type 7 LSAs throughout the backbone.
C. RTA will redistribute the RIP routers into the NSSA as type 5 LSAs. RTB will flood the type 5 LSAs throughout the backbone.
D. RTA will redistribute the RIP routers into the NSSA as type 5 LSAs. RTB will translate the type of 5 LSAs unto type 7 LSAs and flood them throughout the OSPF backbone.
E. RTA will not redistribute the RIP routers into the NSSA.
Correct Answer: A
Route.com is a small IT corporation that is attempting to implement the network shown in the exhibit. Currently the implementation is partially completed. OSPF has been configured on routes Chicago and New York. The S0/0 interface on Chicago and the S0/1 interface on New York are in area 0. The loopback0 on New York is in Area 1. However, they cannot ping from the serial interface of the satellite router to the loopback interface of the New York router. You have been asked to complete the implementation to allow this ping.
ROUTE.com’s corporate implementation guide line requires:
* The OSPF process ID for all routers must be 24.
* The routing protocol for all each interface must be enabled under the routing process.
* The routing protocol must be enabled for each interface using the most specific wild card mask possible.
* The serial link between Seattle and Chicago must be in OSPF area 8.
* OSPF area 8 must not receive any inter-area or external routers.
S0/0 192.168.34.5/30 – link between Seattle and Chicago
Secret Password: Cisco
S0/0 192.168.40.9/30 – link between Chicago and New York
S0/0 192.168.34.6/30 – link between Chicago and New York
Secret Password: Cisco
On Seattle Router:
Router ospf 24
network 192.168.34.5 0.0.0.0 area 8
area 8 stub
On Chicago Router:
Router ospf 24
area 8 stub no-summary
network 192.168.34.6 0.0.0.0 area 8
You are a Network Engineer with ROUTE.com, a small IT company. ROUTE.com has two connections to the internet: one via a frame relay link and one via an EoMPLS link. IT policy requires that all outbound HTTP traffic use the frame relay link when it is available. All other traffic may use either link. No static or default routing is allowed.
Choose and configure the appropriate path selection feature to accomplish this task. You may use the test workstation to generate HTTP traffic to validate your solution.
1. First create the access list that catches the HTTP traffic:
R1#access-list 101 permit tcp any any eq www
2. Configure the route map that sets the next hop address to be ISP1 and permits the rest of the traffic:
R1(config)#route-map pbr permit 10
R1(config-route-map)#match ip address 101
R1(config-route-map)#set ip next-hop 10.1.101.1
R1(config)#route-map pbr permit 20
3. Apply the route-map on the interface to the server in the EIGRP Network:
R1(config-if)#ip policy route-map pbr
Ensurepass offers the Latest 2013 642-902 Exam PDF to pass the exams.