Cisco CCNP 642-902 Exam 04

Ensurepass

QUESTION
Which three statements about the EIGRP routing protocol are true? (Choose three)

A. EIGRP supports five generic packet types, including Hello, Database Description (DBD), Linkstate Request (LSR), Link-State Update (LSU), and LSAck.
B. EIGRP sends periodic hello packets to the multicast IP address 224.0.0.10.
C. EIGRP will not form a neighbor relationship with another peer when their AS number and K values, either or both are mismatched.
D. EIGRP sends periodic hello packets to the multicast IP address 224.0.0.9.
E. EIGRP will form a neighbor relationship with another peer even when their K values are mismatched.
F. EIGRP supports five generic packet types, including Hello, Update, Query, Reply, and ACK packets.

Correct Answer: BCF

QUESTION 12
After DUAL calculations, a router has identified a successor route, but no routes have qualified as a feasible successor. In the event that the current successor goes down, what process will EIGRP use in the selection of a new successor?

A. EIGRP will find the interface with the lowest MAC address
B. The route will transition to the active state
C. The route will transition to the passive state
D. EIGRP will automatically use the route with the lowest feasible distance(FD)
E. EIGRP will automatically use the route with the lowest advertised distance(AD)

Correct Answer: B

QUESTION 13
Refer to the exhibit.

Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 receive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task?

A. R1(config)# router eigrp 1
R1(config-router)# passive-interface serial 0
B. R2(config)# router eigrp 1
R2(config-router)# passive-interface serial 0
C. R1(config)# access-list 20 deny any
R1(config)# router eigrp 1
R1(config-router)# distribute-list 20 out serial 0
D. R2(config)# access-list 20 deny any
R2(config)# router eigrp 1
R2(config-router)# distribute-list 20 out serial 0
E. R1(config)# access-list 20 permit any
R1(config)# router eigrp 1
R1(config-router)# distribute-list 20 in serial 0
F. R2(config)# access-list 20 permit any
R2(config)# router eigrp 1
R2(config-router)# distribute-list 20 in serial 0

Correct Answer: C

QUESTION 14
EIGRP has been configured to operate over Frame Relay multipoint connections. What should the bandwidth command be set to?

A. the CIR rate of the lowest speed connection multiplied by the number of circuits
B. the CIR rate of the lowest speed connection
C. the CIR rate of the highest speed connection
D. the sum of all the CIRs divided by the number of connections

Correct Answer: A

QUESTION 15
Refer to the exhibit.

EIGRP is configured on all routes in the network. On a basis of the show ip eigrp topology output provided, what conclusion can be derived?

A. Router R1 can send traffic destined for network 10.6.1.0/24 out of interface FastEthernet0/0
B. Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out before it declares the neighbor unreachable
C. Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out inquiring for a second successor to network 10.6.1.0/24
D. Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent about network 10.6.1.0/24

Correct Answer: D

Ensurepass offers the Latest 2013 642-902 Exam PDF to pass the exams.