Category Archive » 9TUT 642-902 Dumps

ROUTE 642-902 Training » OSPF Sim

Ensurepass Question OSPF is configured on routers Amani and Lynaic. Amani’s S0/0 interface and Lynaic’s S0/1 interface are in Area 0. Lynaic’s Loopback0 interface is in Area 2. Your task is to configure the following: Portland’s S0/0 interface in Area 1 Amani’s S0/1 interface in Area 1 Use the appropriate mask such that ONLY Portland’s S0/0 and Amnani’s S0/1 could be in Area 1. Area 1 should not receive any external or inter-area routes (except the Read more [...]

ROUTE 642-902 Training » EIGRP Stub Sim

Ensurepass Question By increasing the first distant office, JS manufactures has extended their business. They configured the remote office router (R3) from which they can reach all Corporate subnets. In order to raise network stableness and lower the memory usage and broadband utilization to R3, JS manufactures makes use of route summarization together with the EIGRP Stub Routing feature. Another network engineer is responsible for the implementing of this solution. However, in the process of Read more [...]

ROUTE 642-902 Training » IPv6 OSPF Virtual Link Sim

Ensurepass Question Acme is a small export company that has an existing enterprise network that is running IPv6 OSPFv3. Currently OSPF is configured on all routers. However, R4′s loopback address (FEC0:4:4) cannot be seen in R1′s IPv6 routing table. You are tasked with identifying the cause of this fault and implementing the needed corrective actions that uses OSPF features and does no change the current area assignments. You will know that you have corrected the fault when R4′s Read more [...]

ROUTE 642-902 Training » Policy Based Routing Sim

Ensurepass Question Company Acan has two links which can take it to the Internet. The company policy demands that you use web traffic to be forwarded only to Frame Relay link if available and other traffic can go through any links. No static or default routing is allowed.   Answer and Explanation: Notice: The answer and explanation below are from PeterPan and Helper.Please say thank to them! All the HTTP traffic from the EIGRP Network should go through Frame Relay link if available and Read more [...]

ROUTE 642-902 Training » EIGRP OSPF Redistribution Sim

Ensurepass Question: (Hope someone will contribute the detailed requirement of this sim!) Some information I have gathered so far: R2 is an ASBR for EIGRP 100 and OSPF AREA 24 R3 is an ASBR for EIGRP 100 and OSPF AREA 34 [note: so there are TWO separate areas on TWO separate ASBRS thus you need to do redistribution on R2 and R3 R1 is ONLY in EIGRP 100, and is THE ONLY router you can ping from. R4 has a loopback interface that must be pinged from R1. R4 is running OSPF and has redundant link to Read more [...]

» OSPF Questions 6

EnsurepassHere you will find answers to OSPF Questions – Part 6 Question 1 You are developing a verification plan for an upcoming OSPF implementation. Part of this plan is to verify the status of type 3 LSAs within the network. Which routers should you verify first to ensure that the configurations are correct for generating type 3 LSAs? A. Internal routers within the backbone area (area 0) B. Internal routers within the NSSAs C. Internal routers within the stubby areas D. ASBRs E. ABRs Read more [...]

» ROUTE FAQs & Tips

EnsurepassIn this article, I will try to summarize all the Frequently Asked Questions in the ROUTE 642-902 Exam. Hope it will save you some time searching through the Internet and asking your friends & teachers. 1. Please tell me how many questions in the real ROUTE exam, and how much time to answer them? There are 50 questions, including 4 lab-sims. You have 90 minutes to answer them but if your native language is not English, Cisco allows you a 30-minute exam time extension. 2. How much does Read more [...]

» OSPF Questions 5

EnsurepassHere you will find answers to OSPF Questions – Part 5 Question 1 A network administrator has enabled OSPF across an NBMA network and has issued the command ip ospf network nonbroadcast. Given those facts, which two statements are true? (Choose two) A. DR and BDR elections will occur. B. DR and BDR elections will not occur. C. All routers must be configured in a fully meshed topology with all other routers. D. The neighbor command is required to build adjacencies. E. Interfaces Read more [...]

» Operations Questions

EnsurepassHere you will find answers to Operation questions Question 1 Refer to the exhibit. Will redistributed RIP routes from OSPF Area 2 be allowed in Area 1? A – Because Area 1 is an NSSA, redistributed RIP routes will not be allowed. B – Redistributed RIP routes will be allowed in Area 1 because they will be changed into type 5 LSAs in Area 0 and passed on into Area 1 C – Because NSSA will discard type 7 LSAs, redistributed RIP routes will not be allowed in Area 1 D – Read more [...]

» OSPF Questions 4

EnsurepassHere you will find answers to OSPF Questions – Part 4 Question 1 Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF between them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem? (Choose three) A. RouterC(config-if )#ip ospf network broadcast RouterD(config-if Read more [...]

» IPv6 Questions 3

EnsurepassHere you will find answers to IPv6 Questions – Part 3 Question 1 During the IPv6 autoconfiguration, what does the device append to the 64-bit prefix that it receives from the router to create its IPv6 address? A. a pseudorandom generated number B. its locally configured IPv4 address C. the DHCP-supplied device ID D. its MAC address Answer: D Explanation The automatic configuration is a great feature of IPv6. Imagine you have to manually configure an IPv6 address with 128-bit Read more [...]

» OSPF Questions 3

EnsurepassHere you will find answers to OSPF Questions – Part 3 Question 1 Refer to the exhibit. You are the network administrator responsible for the NProuter, the 10.1.1.1 router, and the 10.1.1.2 router. What can you determine about the OSPF operations from the debug output? NProuter#debug ip ospf events OSPF events debugging is on NProuter# 00:02:03: OSPF: Rev hello from 172.16.1.1 area 0 from Serial0/0 10.1.1.1 00:02:03: OSPF: Mismatched hello parameter from 10.1.1.1 00:02:03: Read more [...]

» EIGRP Simlet

Ensurepass HOT EXAM! 100-105 Dumps VCE PDF 200-105 Dumps VCE PDF 300-101 Dumps VCE PDF 300-115 Dumps VCE PDF 300-135 Dumps VCE PDF 300-320 Dumps VCE PDF 400-101 Dumps VCE PDF 640-911 Dumps VCE PDF 640-916 Dumps VCE PDF Read more [...]

» Redistribute Questions 2

EnsurepassHere you will find answers to Redistribute Questions – Part 2 Question 1 Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribution is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1? A. the routes originating from the RIP routing domain B. the routes originating from the OSPF Read more [...]

» BGP Questions 5

EnsurepassHere you will find answers to BGP Questions – Part 5 Question 1 Above is the output from show ip bgp neighbors command. What is line 21 stating about the BGP connection? BGP neighbor is 172.16.254.3, remote AS 150, internal link 1. BGP version 4, remote router ID 172.16.254.3 2. BGP state = Established, up for 19:24:07 3. Last read 00:00:06, hold time is 180, keepalive interval is 60 seconds 4. Neighbor capabilities: 5. Route refresh:advertised and received(new) 6. Address Read more [...]

» EIGRP Questions 5

EnsurepassHere you will find answers to EIGRP Questions – Part 5 Question 1 Which three descriptions are correct based on the exhibited output? (Choose three) A. R1 is configured with the variance command. B. The route to 10.2.0.0/16 was redistributed into EIGRP. C. A default route has been redistributed into the EIGRP autonomous system. D. R1 is configured with the ip summary-address command. Answer: A C D Explanation From the routing table above, we see that network 172.16.1. can be Read more [...]

» EIGRP Questions 3

EnsurepassHere you will find answers to EIGRP Questions – Part 3 Note: If you are not sure about EIGRP, please read my EIGRP tutorial. Question 1 Refer to the exhibit. ROUTE.com has just implemented this EIGRP network. A network administrator came to you for advice while trying to implement load balancing across part of their EIGRP network. If the variance value is configured as 2 on all routers and all other metric and K values are configured to their default values, traffic from the Internet Read more [...]

» BGP Questions 4

EnsurepassHere you will find answers to BGP Questions – Part 4 Question 1 Which two conditions can cause BGP neighbor establishment to fail? (Choose two) A. There is an access list blocking all TCP traffic between the two BGP neighbors. B. The IBGP neighbor is not directly connected. C. BGP synchronization is enabled in a transit autonomous system with fully-meshed IBGP neighbors. D. The BGP update interval is different between the two BGP neighbors. E. The BGP neighbor is referencing Read more [...]

» EIGRP Questions 2

EnsurepassHere you will find answer to EIGRP Questions – Part 2 Question 1 Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configuration statement should be included on router R4 to advertise a default route to its neighbors? A. R4(config)#ip default-network 10.0.0.0 B. R4(config)#ip route 0.0.0.0 0.0.0.0 10.1.1.1 C. R4(config)#ip route 10.0.0.0 255.0.0.0 10.1.1.1 D. R4(config-router)# default-information originate Answer: A Explanation The Read more [...]

» BGP Questions 3

EnsurepassHere you will find answers to BGP Questions – Part 3 Question 1 Which option is true regarding the synchronization rule? A. Do not use or internally advertise a route until the route is learned from a source other than BGP. B. Do not use or advertise a route until the route is learned from a BGP peer. C. Do not use or advertise routes marked PARTIAL. D. Wait until a CONFIRM message is received before using routes from BGP neighbors. Answer: A Explanation The complete synchronization Read more [...]

» OSPF Hotspot

EnsurepassHere you will find answers to OSPF Hotspot Questions Question The company and the company network have both been growing rapidly. Multiple adds, moves and changes have been applied to the network. Your boss has asked you to troubleshoot a recent OSPF synchronization problem that has arisen. There have been synchronization problems at separate locations in the OSPF area 0. There have been reported link failures during the rapid growth of the company network. You are required to resolve Read more [...]

» BGP Questions

EnsurepassHere you will find answers to BGP questions Question 1 Refer to the exhibit. Router RIP is attempting to establish BGP neighbor relationships with routers RT1 and RT3. On the basis of the information that is presented in the exhibit, which two statements are true? (Choose two) A – RTR has a BGP password set but neighbor 10.0.0.1 does not B – RTR has a BGP password set but neighbor 10.0.0.5 does not C – RTR has a BGP password set but neighbor 10.0.0.1 has an incorrect Read more [...]

» BGP Questions 3

EnsurepassHere you will find answers to BGP Questions – Part 3 Question 1 Which option is true regarding the synchronization rule? A. Do not use or internally advertise a route until the route is learned from a source other than BGP. B. Do not use or advertise a route until the route is learned from a BGP peer. C. Do not use or advertise routes marked PARTIAL. D. Wait until a CONFIRM message is received before using routes from BGP neighbors. Answer: A Explanation The complete synchronization Read more [...]

» EIGRP Simlet

Ensurepass HOT EXAM! 100-105 Dumps VCE PDF 200-105 Dumps VCE PDF 300-101 Dumps VCE PDF 300-115 Dumps VCE PDF 300-135 Dumps VCE PDF 300-320 Dumps VCE PDF 400-101 Dumps VCE PDF 640-911 Dumps VCE PDF 640-916 Dumps VCE PDF Read more [...]

» IPv6 Questions 2

EnsurepassHere you will find answer to IPv6 Questions – Part 2 Question 1 Refer to the exhibit. In the show ipv6 route output, what would the metric be for a summary route that summarizes all three OSPFv3 routes displayed?   A. 20 B. 40 C. 100 D. 120 E. 140 F. 160   Answer: C Explanation The metric of a summary route is the highest cost of the routes being summarized. Therefore when summarizing three routes above the highest cost (100) will be chosen. Question Read more [...]

» BGP Questions 2

EnsurepassHere you will find answers to BGP Questions – Part 2 Question 1 Study the configuration presented in the exhibit carefully. What is the objective of the route map named test? router bgp 50001 network 10.0.0.0 network 172.16.0.0 neighbor 10.1.1.1 remote-as 5003 neighbor 10.1.1.1 route-map test out ! access-list 1 permit 10.0.0.0 access-list 2 permit any ! route-map test permit 10 match ip address 1 set metric 200 ! route-map test permit 20 match ip address 2 A. Read more [...]

» IPv6 Questions

EnsurepassHere you will find answers to IPv6 questions If you are not sure about IPv6, please read my IPv6 tutorial Question 1 Which two reductions are the correct reductions of the IPv6 address 2001:0d02:0000:0000:0014:0000:0000:0095? (Choose two) A – 2001:0d02:::0014:::0095 B – 2001:d02::14::95 C – 2001:d02:0:0:14::95 D – 2001:d02::14:0:0:95 Answer: C D Explanation A is not correct because we can’t use triple colons (:::) in IPv6 presentation. B is not correct Read more [...]

» BGP Questions

EnsurepassHere you will find answers to BGP questions Question 1 Refer to the exhibit. Router RIP is attempting to establish BGP neighbor relationships with routers RT1 and RT3. On the basis of the information that is presented in the exhibit, which two statements are true? (Choose two) A – RTR has a BGP password set but neighbor 10.0.0.1 does not B – RTR has a BGP password set but neighbor 10.0.0.5 does not C – RTR has a BGP password set but neighbor 10.0.0.1 has an incorrect Read more [...]

» Policy Based Routing Questions

EnsurepassHere you will find answers to Policy Based Routing Questions Question 1 Refer to the exhibit. Based upon the configuration, you need to understand why the policy routing match counts are not increasing. Which would be the first logical step to take? A. Confirm if there are other problematic route-map statements that precede divert. B. Check the access list for log hits. C. Check the routing table for 212.50.185.126. D. Remove any two of the set clauses. (Multiple set clause entries Read more [...]

» EIGRP Questions 4

EnsurepassHere you will find answers to EIGRP – Part 4 Question 1 Which three statements are true about EIGRP route summarization? (Choose three) A. Manual route summarization is configured in router configuration mode when the router is configured for EIGRP routing. B. Manual route summarization is configured on the interface. C. When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routes. D. The ip summary-address Read more [...]

» OSPF Questions 7

EnsurepassHere you will find answers to OSPF Questions – Part 7 Question 1 Refer to the exhibit. ROUTE.com is planning to implement a new secure OSPF network to support traffic between clients on the 172.16.10.0/24 network and the file server on the 172.16.20.0/24 network. You have been asked to review the implementation plan for the OSPF project. Which statement about the plan is true? A. It is complete as written. B. It should include a task that shuts down all unused interfaces. Read more [...]

» Redistribute Questions 3

EnsurepassHere you will find answers to Redistribute Questions – Part 3 Question 1 Given the accompanying output, which additional command is needed to redistribute IGRP into EIGRP? Router eigrp 123 Network 10.10.10.0 No auto-summary ! Router igrp 123 Network 172.16.0.0 Network 172.17.0.0 A. Under the router igrp mode add redistribute eigrp 123 B. Under the router eigrp mode add redistribute igrp 123 C. Under the router eigrp mode add redistribute igrp 123 subnets D. None, Read more [...]

» Redistribute Questions 2

EnsurepassHere you will find answers to Redistribute Questions – Part 2 Question 1 Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribution is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1? A. the routes originating from the RIP routing domain B. the routes originating from the OSPF Read more [...]

» EIGRP Questions

EnsurepassHere you will find answers to EIGRP questions Question 1 Which three statements about the EIGRP routing protocol are true? (Choose three) A – EIGRP sends periodic hello packets to the multicast IP address 224.0.0.9 B – EIGRP sends periodic hello packets to the multicast IP address 224.0.0.10 C – EIGRP supports five generic packet types. including hello, update, query, reply, and ACK packets D – EIGRP supports five generic packet types, including hello, database Read more [...]